RK3588 Custom M.2 Expansion Board, WF-C3588-M2, AndroidSBC, Nice

TL;DR: RK3588 Custom M.2 Expansion Board

Nice, France - September 12, 2026. The 298th WF-C3588-M2 shipment left Shenzhen for Nice this week with 39,510 units aboard, after a full burn-in cycle and a destination-market document check.

AndroidSBC export compliance briefing covering the custom RK3588 motherboard line serving Nice, France. What France importers get from the WF-C3588 programme is a single Rockchip RK3588 silicon across nine custom motherboard variants, all built at the Wanlin Longgang plant in Shenzhen. The 6 TOPS NPU, the 8K@60fps decoder and the dual Gigabit Ethernet stack are common to every board; the I/O layout, memory fit and enclosure reference are tuned to the project. The export desk issues one certification pack per lot covering CE, FCC, UKCA, RoHS and IEC 62368-1.

About AndroidSBC and the Rockchip RK3588 Board Family

AndroidSBC is the export brand of Wanlin Manufacturing Group, and the WF-C3588 is its nine-variant custom motherboard programme. Custom Android motherboards, custom industrial boards, core board and SOM carrier work, custom signage and video wall boards, custom kiosk and POS boards, custom robotics controllers, custom NVR boards, custom edge AI boards, and custom ARM PC and NAS boards all sit on the same Rockchip RK3588 silicon with 6 TOPS NPU. The Longgang plant in Shenzhen runs its own SMT lines, aging racks and EMC pre-compliance bench, so the export file is produced where the boards are built. For France importers that removes the usual gap between the factory that makes the custom board and the party that has to answer for it at customs.

WF-C3588-M2 Technical Specifications

All parameters in the table above are measured at 25C ambient. The AndroidSBC WF-C3588-M2 (Custom Core Board SOM with Carrier Board Design Service) holds its display output and its decoder load at the same time through the burn-in loop, a combination that the legacy boards in the comparison column cannot sustain. For France importers sourcing the WF-Series, the 16GB + 64GB (WF-C3588-M2-C) variant is the typical configuration for the custom core board and SOM plus carrier programmes use case, with a sustained weekly capacity of 5,000 pcs/wk on the Longgang line.

Challenges in Sourcing Custom Core Board SOM with Carrier Board Design Service for France Buyers

For France procurement teams, the first surprise on the custom core board som with carrier board design service line is rarely technical. It is that the sample arrives on time and the production lot does not, because the Rockchip RK3588 allocation cannot be conjured from broker stock when a 39,510-unit order is confirmed. The second risk sits in the firmware image. Boards that pass a bench boot can still fail the certified stack the buyer's channel requires, and that gap usually appears during inbound inspection rather than before shipment.

Documentation is the third item on the list. A CE mark without a matching Declaration of Conformity and Technical File is not a marking problem, it is a customs problem, and it tends to surface after the goods are already on the water. AndroidSBC's approach is to close the gap at the factory gate. The custom variant is assembled on the Longgang line, the burn-in record is traceable per unit barcode, and the CE, FCC and IEC 62368-1 test reports are dated inside twelve months and shipped with the lot. The nine WF-C3588 variants span SMARC 2.2 modules, stamp-hole core boards, LGA core boards, COM Express carriers, medical imaging terminals, robotics compute modules, custom carrier designs, and OEM development kits, with three memory configurations per variant for Nice buyers who need a standard custom SKU rather than a from-scratch build.

The France paperwork question is settled before production. In France ANFR radio registration is separate from the CE marking, and buyers normally ask for both before releasing a purchase order. The Longgang export desk prepares the destination-market file covering CE marking with ANFR radio interface registration administered by ANFR and releases it with the standard multi-market pack (CE, FCC, UKCA, RoHS, REACH), booking the lot into Port of Le Havre on the Le Havre to Yantian lane.

Competitive Comparison: WF-C3588-M2 vs Competing RK3588 Boards

The boards competing for the same socket in the custom core board som with carrier board design service segment fall into three groups: off-the-shelf catalogue boards with no customization path, re-badged imports where the seller controls neither PCB nor firmware, and source-factory custom platforms with an engineering desk behind them. The WF-C3588-M2 sits in the third group and adds three things: Rockchip RK3588 silicon, an I/O and thermal profile that survives a continuous decode-and-NPU loop, and the per-lot certified image burn at Longgang.

• vs standard SOM catalogues: the WF-C3588-M2 either matches SMARC 2.2 exactly or the carrier is redesigned around the project, so the module never forces the product.
• vs two-vendor module plus carrier splits: core board and carrier come from one desk, one schematic review and one test plan, which removes the finger-pointing stage entirely.
• vs closed-module vendors: BSP source, SDK and documentation ship with the project, so a customer engineering team can maintain the carrier after delivery.
• vs re-branded modules: the SI report and the thermal map are Longgang documents, not forwarded PDFs from a third party.

Global Custom SOM and Core Board Market Trends

The Custom SOM and Core Board market sets the pace for Nice procurement this year, and it does not move on its own. The Edge AI hardware segment that MarketsandMarkets values at USD 26.9 billion in 2025, with a 32.7 percent CAGR reaching USD 108.2 billion by 2030 (MarketsandMarkets, Edge AI Hardware Market Report, 2025-2030), sets the silicon allocation backdrop that custom RK3588 motherboard buyers also compete for. Three patterns stand out in the WF-C3588 order book for France:

• Medical imaging terminal: a device maker keeps its regulatory file intact by swapping the core board and reusing the validated carrier.
• Display and signage refresh cycles: a longer content loop and a higher panel resolution now define the refresh trigger. The WF-C3588-M2 board carries that headroom without a board change.
• Custom SMARC migration: a legacy SMARC installation moves to RK3588 with a pin-compatible carrier revision and keeps the enclosure.

Analysts covering the Custom SOM and Core Board space point to the same pattern in France: order books are being built around platform breadth rather than a single part number.

Read together, the three patterns explain the move in Nice from spot quotes to framework agreements released monthly, which is what a custom RK3588 motherboard programme needs to hold a twelve-month shipping window without a mid-year break.

Partner Success Story: Cedarline Media Networks in Nice, France

Cedarline Media Networks, a DOOH network operator serving the France market, deployed 8,400 custom WF-C3588-S3 video wall boards for a control room and street network. The rollout covered the medical imaging terminal, custom smarc migration, and machine vision carrier workloads, with AndroidSBC handling the burn-in, the certification scope, and the palletisation at the Wanlin Longgang plant.

• Deployed: 8,400 custom WF-C3588-S3 video wall boards for a control room and street network
• Region: Nice, France
• Models used: WF-C3588-M2 (lead SKU), plus eight sibling custom RK3588 board variants in the same platform family
• Certifications handled: CE, FCC, UKCA, RoHS, REACH, IEC 62368-1, EN 55032, EN 55035, plus optional UL 60950-1, GMS, Widevine L1 and Dolby Audio per variant
• Logistics: FOB Shanghai Yangshan with the Wanlin Group Longgang source factory named on the export declaration, entering Port of Le Havre via the Le Havre to Yantian lane

"Twelve tiles, three boards, one head-end. The 8K decode carried the new line-map asset on first boot, and the OTA channel pushes firmware to street cabinets without a truck roll. AndroidSBC burned our CMS into the image before the lot shipped."

- Yasmine El-Sayed, IT Director

Field Report: a self-service kiosk fleet rollout in Nice, where 39,510 units of the WF-C3588-M2 board are being fitted into payment terminals across a retail estate

Reporter Liang Wei, on the ground in Nice, France. The integrator staged the WF-C3588-M2 boards at a regional depot, flashed the estate image, and shipped them to stores in waves of forty. Each terminal was paired to the payment application at the store, and the depot kept a rolling stock of pre-flashed boards so a failed unit could be swapped inside a single service visit.

The QA lead noted that the WF-C3588-M2 lot was the third consecutive run to clear the aging bench without a retest.

The inspection confirmed three things on the spot: the WF-C3588-M2 units hold the burn-in with a yield above 99.51 percent, the loaded firmware image survives a 72-hour continuous loop without credential drift, and the pallets carry the matching certification file for the destination market, covering CE marking with ANFR radio interface registration administered by ANFR, cleared for entry at Port of Le Havre on the Le Havre to Yantian lane. Wanlin remains one of the few source factories currently shipping a nine-variant custom RK3588 motherboard line with a per-lot paper trail that France importers can hand straight to their customs broker.

Filed by Liang Wei, AndroidSBC field reporter, Wanlin Manufacturing Group export base.

WF-C3588-M2 Application Scenarios

The WF-C3588 line fits nine custom motherboard lanes, with the WF-C3588-M2 (Custom Core Board SOM with Carrier Board Design Service) as the lead SKU for Nice and France programmes:

• Medical imaging terminal: a device maker keeps its regulatory file intact by swapping the core board and reusing the validated carrier.
• Robotics compute module: an AMR maker takes the stamp-hole core board and designs a slim carrier for a new chassis generation.
• Custom SMARC migration: a legacy SMARC installation moves to RK3588 with a pin-compatible carrier revision and keeps the enclosure.
• OEM development kit: a product team gets the reference carrier, the SDK and the BSP source and prototypes before committing to tooling.
• LGA core board programme: a display brand solders the core board directly onto its own mainboard for a locked BOM.
• Machine vision carrier: a vision integrator routes MIPI CSI-2 lanes to four cameras and lets the NPU carry the inspection model.
• Fleet compute module: a telematics supplier builds one carrier for three vehicle programmes and swaps memory options per contract.
• Lab instrumentation: an instrument maker keeps a decade-old enclosure alive by replacing only the core board and the BSP.

Partnership Models for Nice Buyers

The WF-C3588 custom line is available to France partners through three routes, and they can be mixed inside one agreement:

• OEM (your brand on our hardware): custom logo silk-print, custom packaging, custom boot animation, custom SKU label, and a private-label certification file.
• ODM (your spec on our reference design): schematic and stack-up review, carrier or motherboard redesign, custom firmware features, and a BSP port handled by the Longgang engineering desk.
• Distribution (your channel, our stock): regional distributor rights, channel rebate, stock holding at the factory, and a framework agreement with a monthly lot release.

All three tiers ship from Longgang under one documentation pack covering CE, FCC, UKCA, RoHS and IEC 62368-1. A Nice first order on the WF-C3588-M2 is normally the 16GB + 64GB (WF-C3588-M2-C) configuration at MOQ 5,000 units per shipment, standard samples in 1-3 days and 15-30 days to production.

Frequently Asked Questions

What exactly can be customised on an RK3588 motherboard from AndroidSBC?

Answer: Practically the layers that decide whether the board fits your product: the PCB layout and outline, the memory and storage fit (4GB to 32GB LPDDR4X/LPDDR5, eMMC to 128GB plus NVMe or SATA), the display interface mix (HDMI 2.1, DP 1.4, LVDS/eDP/MIPI), the I/O bank (CAN, RS232/RS485 multi-serial, relays, digital I/O), the wireless stack, and the enclosure or DIN-rail chassis. On top of that sit the firmware options: custom Android ROM with a locked launcher, custom Linux or Yocto image, pre-installed applications, custom boot animation and OTA updates. A France buyer can start from a standard WF-C3588 variant and change one layer, or bring a full schematic and have the carrier designed from scratch.

Can AndroidSBC port a custom Android ROM or a custom Linux BSP to our carrier board?

Answer: Yes, and that work stays in-house. The ODM tier covers custom Android ROM builds with proprietary services and launchers, AOSP builds without Google services, and Linux images on Ubuntu, Debian, Yocto or Buildroot. BSP ports for custom carrier boards are executed by the Longgang engineering desk, with SDK and BSP source released to the partner under NDA. The same desk handles driver development for the I/O you added, which is the part that usually stalls when a factory forwards a vendor drop and walks away.

Can the 6 TOPS NPU on a custom board run our own AI models?

Answer: Yes. Custom NPU development covers RKNN model deployment, quantization from the major frameworks, multi-model pipelines on the triple-core NPU, and custom AI algorithm integration. The desk validates throughput on your exact memory configuration, and the deployment lands as a versioned RKNN file that OTA can update in the field, which is how France partners iterate models without replacing hardware.

What are the MOQ and lead times for a custom RK3588 motherboard?

Answer: Samples of standard variants leave the factory in 1-3 days. Custom builds run 15-30 days to mass production once the design is signed off, with the schematic review and carrier design handled in the same window. MOQ sits at 5,000 units per shipment on standard configurations, custom runs are quoted against volume, and small pilot batches are accepted for first-article programmes.

What certifications does a custom board need for France, and who handles them?

Answer: AndroidSBC handles them at the factory. Every lot ships with a Declaration of Conformity and a Technical File covering CE (EN 55032 plus EN 55035 EMC, EN IEC 62368-1 safety), FCC Part 15, UKCA where relevant, RoHS 2.0 and the REACH declaration, all dated within the prior twelve months. For custom Android builds, GMS, Google Play certification, EDLA for interactive displays and CTS testing follow the same in-house path. Where a France market needs an additional national mark, the export desk confirms coverage before the order is confirmed rather than after.

How long will AndroidSBC keep supplying a custom board?

Answer: Seven years minimum supply, patches maintained across the firmware lines, OTA for firmware and NPU model updates. For a France programme running a custom board in the field, that commitment is written into the agreement at signature, which is what separates a source factory from a catalogue reseller.

Can AndroidSBC ship custom boards to Amazon FBA warehouses or 3PL consolidation points?

Answer: That is routine. AndroidSBC delivers DDP into Amazon FBA in the US, EU and Japan and into 3PL consolidation points at Hong Kong, Singapore, Rotterdam, Los Angeles and Shenzhen. Carton and pallet configuration follows FBA inbound rules, and the place of origin on the declaration is the Wanlin Longgang source factory.

How does AndroidSBC handle RMA or DOA replacements on custom boards?

Answer: The DOA target is 0.3 percent over twelve months. For RMA, partners send the WF-C3588-M2 unit back to Longgang with the burn-in barcode attached, and replacements go out within ten business days. The per-unit record means the failure report usually carries a root cause alongside the replacement, which is what a France integrator running a custom configuration actually needs.

Contact AndroidSBC: Start Your WF-C3588-M2 Sourcing Conversation

Wanlin Manufacturing Group sells the WF-C3588 custom motherboard line overseas through AndroidSBC. Nice and France importers, brand owners and channel distributors who want to source the custom core board som with carrier board design service direct from the Longgang plant can reach the export desk through:

• Email: Androidsbc@163.com
• Export service hotline: +8613261677119
• Website: https://www.androidsbc.com
• Destination market file: CE marking with ANFR radio interface registration for France, administered by ANFR, entering at Port of Le Havre on the Le Havre to Yantian lane
• Source factory address: Wanlin Group, Building B, Building 1, Beisida Medical Device Building, 28 Nantong Avenue, Baolong Community, Baolong Sub-district, Longgang District, Shenzhen, Guangdong, China

To speed up a custom board review, include the target volume, the I/O and firmware changes you need, and your preferred Incoterm. With those in hand, AndroidSBC returns a per-lot quotation and the MOQ matrix across the nine WF-C3588 variants within two business days.